Advantapure - Newage Industries
Tube And Fitting
High Purity Diaphragm Valve
Hoses
Gasket
Sanitary Pump
Tube Support
Sanitary Ball Valve
Sanitary Butterfly Valve
Sanitary Check Valve
VCR And Compression Fitting
General Industries
Angle Stem Bottom Tank Valve
Fire Test Valve
Cryogenic Valve
Inline Sampling Valve
Multiport Valve
 
PRODUCTS > IGENIX FORGED/CAST SANITARY BALL VALVE

Forged valves
SI-SERIES 8 (1/2” through 4”, DIN 11850 DN 8 through DN 100, ISO 1127 DN 8 through DN 80) PBM’s Forged IGENIX® Sanitary Series 8, “True Bore®” ball valve with port through ball, seats, and end fittings same as ID of tubing. Forged 316L stainless steel body and end fittings per ASTM A182F316L / DIN 1.4404, wrought or forged 316L ball and stem, less than 1% ferrite, three piece swing-out valve design. Seats and seals shall be white TFMTM. Seats shall provide both upstream and downstream seal and be adjustable for inline wear. Stem packing shall be live loaded white TFMTM and S-TEF® material. End fittings shall match to tubing connections. Orbital weld end fittings should have wall thickness to match connecting tubing and have a controlled sulfur content of 0.005% through 0.017%. Valves shall not require disassembly for welding. Body bolts and nuts shall be 18-8 stainless steel. Interior surfaces shall be 20 RA or better with optional electropolish and finer mechanical finishes. Valve shall have integral mounting pad to allow adaptation to ISO 5211 for direct mount automation. All materials are FDA and USP23 Class VI compliant. Maximum working pressure to be 600 PSIG, but is limited based on valve size, valve material and end fitting type. Valves are full vacuum.

CS-SERIES 8 (1/2” through 4”, DIN 11850 DN 8 through DN 100, ISO 1127 DN 8 through DN 80) PBM’s IGENIX® Clean Steam Series 8. Same Specification as SI-Series 8 above. Add text “Seats and seals shall be white TFMTM with FDA approved EPR O-ring energizer. Seats shall have stainless steel encapsulation on ID. Body seal shall be FDA approved EPR o-rings with white TFMTM back up seal. Optional 300 Series s/s 4” stem extension with locking lever handle for 4” thick installation.

CAST VALVES
SI-SERIES 9 (1/2” through 6”, DIN 11850 DN 8 through DN 150, ISO 1127 DN 8 through DN 100) PBM’s IGENIX® Sanitary Series 9 “True Bore®” ball valve with port through ball, seats, and end fittings same as ID of tubing. Type (316 L stainless steel with less than 2% ferrite, Hastelloy® C-276 or C22®, or other) body, ball, stem, and end fittings, three piece swing-out valve design. Seats and seals shall be combined “cartridge” and be white TFMTM. Seats shall provide both upstream and downstream seal and be adjustable for in-line wear. Stem packing shall be live loaded white TFMTM or S-TEF® material. End fittings shall match to tubing connections. Orbital weld end fittings should have wall thickness to match connecting tubing and have a controlled sulfur content of .005% through .017%. Valves shall not require disassembly for welding. Body bolts and nuts shall be 18-8 stainless steel. I.D. and O.D. surface finish shall be the same as specified for tubing. Maximum working pressure to be 900 PSIG, but is limited based on valve size, valve material and end fitting type. Valves are full vacuum. Valves shall be non-fire rated design unless otherwise specified. To add automation and controls, see section “Automation and controls”. CS-SERIES 9 (1/2” through 6”): PBM’s IGENIX® Clean Steam Series 9, Same specification as SI (cast) above. Add text “Seats shall be white TFMTM with FDA approved EPR O-ring energizer. Seats shall have stainless steel encapsulation on ID. Optional 300 Series s/s stem extensions for thick insulation.

CT-SERIES 8 (forged) OR SERIES 9 (cast): PBM’s IGENIX® Clean Steam Series 8 or 9. Same specification as CS forged or cast above. Add text. ”Valve shall have a dual chamber seat design to allow for a 1/2” Tri-Clamp® steam drain purge port positioned in the valve body to facilitate drainage of the body cavity to the trap. Ball shall have 2 steam purge holes to allow steam condensate to flow past seats in closed position to trap. Stem packing shall be live loaded white TFMTM and S-TEF®. Provide a 90˚ 2-position or 180˚ 3-position stainless steel handle with blue vinyl grip for closed/open, and/or trap isolated valve positions. A locking handle position mechanism shall be available if required.